CRTF1240AS0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patrick from BIRMINGHAM, AL
- Parts Used:
- 131461200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace Drain Hose
Ordered this part to replace a drain hose that had been cut short on the washer. Installation was straight-forward. Removed the two front screws to access the cabinet. Locate the drain hose and remove with a pair of pliers. Install the new part and attach the clamp with the pliers just like removal. Took about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from ST MICHAELS, MD
- Parts Used:
- 131763256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer door wouldn't lock so it would not run
Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from LOVINGTON, NM
- Parts Used:
- 131763310
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Catch on door strike broke.
Removed and replaced two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theresa from W SACRAMENTO, CA
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
off balance and walking
the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tami from INDIANAPOLIS, IN
- Parts Used:
- 131763310
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The small plastic piece broke that locked the door.
Screwed the new part back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blake from WINTER HAVEN, FL
- Parts Used:
- 5304485917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Broken shock
Watched the video on website and followed what they said. Worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from COMMERCE TWP, MI
- Parts Used:
- 134144700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer was bouncing and emitted a banging noise only when on high speed spin
I watched the videos and replaced the shocks and suspension springs. This worked to stop the unit bouncing completely and cut the banging noise in half. Further diagnosis revealed a damaged drum and outer shell. The repair itself was very simple and didn't require special tools or skills. There is a tricky shock absorber locking pin on the right shock bottom position. There is a control box of some sort that prevents the complete removal of the pin without breaking it. On install, I simply pushed the pin through from the front. Ultimately, I ended up replacing the unit. However, I found the site to be extremely helpful. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from PARKERSBURG, WV
- Parts Used:
- 137108000
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
Water would not always drain from the wash tub.
Simple install, remove the two screws holding the pump motor.
Loosen the two hose clamps that hold the hoses in place.
Pull out old pump motor.
Place new pump into place, and install mounting screws and tighten.
Slip drain hoses onto new pump and reinstall clamps.
Check for leaks.
Done.
Loosen the two hose clamps that hold the hoses in place.
Pull out old pump motor.
Place new pump into place, and install mounting screws and tighten.
Slip drain hoses onto new pump and reinstall clamps.
Check for leaks.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from VANDALIA, IL
- Parts Used:
- 137108000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Drain pump was out
Repair was easy watched video it was spot on I went to auto parts store and bought 2 screw clamps to replace the spring clamps and made repairs easier washer works great happy wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from CHARLEVOIX, MI
- Parts Used:
- 134051000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
WASHER WASN'T SPINNING OUT ANYMORE.
Pulled the back off and it was right there. Hardest part was to get the belt all the way around the drive wheel on the washer tub. Found out that it wasn't just the belt. It is the shock absorbers that probably broke the belt, even though the belt was probably well over 15 years old. The bouncing and banging because of the absorbers being bad probably had something to do with the belt eventually breaking. Now, we need to replace the shock absorbers.A big thing to remember about the belt install....clean the drive wheel real good!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from VALPARAISO, FL
- Parts Used:
- 5304485917, 134144700
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Spring broke and front loading washer made loud noise when it went into spin cycle.
Removed the back and lower panel in the front of machine. Turned it on its side to replace spring, not tools required. Then stood it up and replaced both shocks by removing plastic pins that hold them in place, no tools required. The only time you need tools is to remove the metal panels to get to the parts. Now it makes no noise and runs like a new washer. Paid $140 for the parts, a new machine would have cost over a thousand and would be one of those digital nightmares that don't last as long. This machine is 18 years old.
Was this instruction helpful to you?
Thank you for voting!
Washer would not spin. Water remained in tub.
First of all I looked up the possible causes at partselect.com. The two likely choices were a door switch and/or the drain pump. I changed the door switch first. I removed the spring from the black boot. Pulled the boot away from the machine on the door switch side. Just the screw driver to remove the mounting screws from the from of the machine. This holds the door sw on the machine. After removing the screws i disconnected the wiring from the door sw. The wiring snaps in place. I then reversed this process and ran the machine. It worked so I didn't have to change the drain pump. I am keeping for backup as I have six of these washers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Henderson, NV
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing Machine would drain but not spin.
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Amherst, WI
- Parts Used:
- 137108000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Wouldn't drain water...thus no spin cycle!
Let's see...removed lower panel-used tools to unscrew the unit---one piece-nice to replace---EASY to replace! Removed hose---placed hose on new unit; screwed all back to bottom of washer-replaced lower panel...Voila! Made sure unit was balanced...did a load of whites---Awesome WASHER NOW!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brandon, FL
- Parts Used:
- 131461200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water leaking from bottom hose
remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.
Was this instruction helpful to you?
Thank you for voting!