Admiral Parts

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11746591

Manufacturer Part Number

WP8565925

This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.

★★★★★

★★★★★

5 Reviews

Fix Number

FIX373088

Manufacturer Part Number

4392067

The Whirlpool Dryer Repair Kit is a genuine OEM maintenance kit designed to resolve common issues such as squeaking, thumping, or poor drum rotation in 27-inch dryers. This all-in-one kit is compatible with a wide range of brands, including Whirlpool, Kenmore, Maytag, and others that share the same dryer design. It includes one drum belt, two drum support rollers, one idler pulley, two mounting clips, and one washer—everything needed to restore smooth and quiet operation. The parts are designed for durability and a precise fit, ensuring your dryer performs like new. Installation is considered a moderate DIY task and requires basic tools such as a screwdriver and socket set. Before beginning any repair, make sure to disconnect the dryer from power to ensure safety. This repair kit offers a cost-effective way to extend the life of your appliance and reduce noise, saving you from more expensive repairs or replacements down the line.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX373087

Manufacturer Part Number

4392065

This is an authentic drum support roller kit for 29-inch-wide dryers. It includes 1 belt, 2 roller wheels and an idler pulley. The parts in this kit allow the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension needed for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If these parts are damaged, it could cause loud noises such as squeaking and squealing while the drum is turning. These are normal wear parts and are best replaced as a kit to ensure optimal performance.

★★★★★

★★★★★

20 Reviews

Fix Number

FIX346995

Manufacturer Part Number

341241

This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX334313

Manufacturer Part Number

279838

Sourced directly from the manufacturer, this heating element is an OEM approved replacement part for a variety of dryers and is sold individually. It measures approximately 10.5 inches long, 7.5 inches wide and 2 inches deep. The heating element is the primary source of heat used to dry the clothes in your dryer. This heating element is strung with a coiled wire made of a nickel and chrome alloy. It may need to be replaced if your dryer does not produce heat, if it produces too much heat, or if it will not turn on. If your dryer does not heat, first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases, the heating element will have a break in the element, making it defective. For this repair you will need a quarter inch nut driver and a pair of needle nose pliers. Start this repair by disconnecting the power and then remove the dryer vent. This repair is done from the back of the appliance with the back panel removed. With the panel removed, this will give you access to the heater element. Your next step is to remove the high-limit thermostat from the housing and remove the two wires from the heater terminals. Now remove the screws securing the element to the housing and slide the element out. Installation of the new part is done in the reverse order.

★★★★★

★★★★★

16 Reviews

Fix Number

FIX11741460

Manufacturer Part Number

WP3392519

The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX438018

Manufacturer Part Number

316075103

This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. Please remember to disconnect the power to your oven before you start your repair. Next, remove the 2 screws securing the old element, pull it out, and discard. Connect the new element prongs where the old element fit and screw it back in place. This is a very simple repair that anyone can do.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX11741416

Manufacturer Part Number

WP3387747

When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX11703285

Manufacturer Part Number

W10779716

This authentic OEM bake element is square in shape with the terminals in the center and sits at the bottom of your oven. The purpose of this part is to heat your oven in order to cook your food. If your oven is not coming up to temperature, has hot spots, or will not heat up at all, you may need to replace the bake element. To complete this repair, you will need to disconnect the power to the appliance along with pulling it out far enough to access the back panel. Please note that the new element may look different from the original part in your range, but the replacement part will work with your model.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX10065979

Manufacturer Part Number

W10712395

This OEM dishwasher upper rack adjuster kit includes the left and ride side adjusters and all the parts needed to repair the upper rack. These parts have changed from plastic to metal, so even though it looks different than the original part, it is made to be perfectly compatible. This part is located on the dishwasher rack and is connected to the track, allowing it to move in and out smoothly. If this part is damaged, it may make it difficult to move the rack in and out or it might hang down awkwardly, indicating a repair is needed.