Troy-Bilt Parts

Fix Number

FIX19305064

Manufacturer Part Number

946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX19272260

Manufacturer Part Number

734-04018C

This is a genuine OEM replacement part, it is sold individually. This is the front wheel on the models shown below. There are two of them on each mower. The wheel has a ring gear on the inside which is driven by the Right hand and Left hand smaller gear that attaches to the front axle on the transmission assembly.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX9988561

Manufacturer Part Number

647-04271-0637

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is collecting grass clippings. To install or replace the grass bag frame requires no tools. This part is made of metal and is sold individually.

Fix Number

FIX9110822

Manufacturer Part Number

738-04124A

Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX11813377

Manufacturer Part Number

946-05124A

This is an authentic OEM part. The MTD deck engage cable is composed of metal and plastic parts, and has been designed for use in several tractor machines. This part is fastened onto the frame assembly. The deck engage cable works to move belt idler pulley and engage the cutting blades. Please refer to manual for specific repair instructions. A wrench and a screwdriver is helpful in making the replacement. This part is sold individually.

Fix Number

FIX16424685

Manufacturer Part Number

749-05084B-0637

This replacement handle is a genuine OEM sourced part. It is specially manufactured for walk behind and push lawn mowers. Upper handle allows user to control the lawn mower. It is attached to the lower handle assembly that is sold separately. This part is made out of metal and is sold individually. Please note, the control bar, knobs and cables are all sold separately. You will need a wrench to replace this upper handle. • Disconnect the bail bar • Detach the control cable • Remove the bolts and the nuts that secure upper handle • Secure the new handle using the same hardware • Reattach the bar and the control cable

Fix Number

FIX9118299

Manufacturer Part Number

753-06183

This is an authentically sourced fuel tank assembly, including the fuel lines, fuel cap, fuel filter, and screws needed for assembly. This fuel tank assembly is for trimmers, and is where the fuel is filtered and stored for use with the engine. Due to its constant contact with fuel, especially if fuel has been left it in for extended periods of time, it may crack, in which case it should be replaced immediately. Leaking gas is very dangerous, so it is important that it get fixed quickly. Before beginning this repair, drain the gas from the tank before installing the new one.

Fix Number

FIX16463287

Manufacturer Part Number

942-04308A

This mower blade is designed for use on 42-inch cutting decks and supports efficient grass cutting for bagging or side-discharge applications. Its durable construction and balanced design help deliver a clean, even cut while maintaining smooth operation during mowing. Replacing a worn or damaged blade restores cutting performance, improves lawn appearance, and helps ensure reliable, consistent operation of the mower throughout the season.

Fix Number

FIX9119300

Manufacturer Part Number

753-06190

A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.

★★★★★

★★★★★

1 Review

Fix Number

FIX9169783

Manufacturer Part Number

942-0741A

This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces along the edges of the blade. If installed correctly this part will keep the grass clipping under the deck longer, and re-cut them. The blade is 21 inches long, and sold individually.