MSD2433HEW Maytag Refrigerator - Instructions

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

Turn off freezer.
Pull the shelves out of freezer.
Remove two screws that hold on back panel.
Melt ice off of cooling fins with hair dryer.
Remove heating element by unplugging heating element on top of fins, pull off wiring with small unit clipped to tubing, slide the wires out from the side of the fins, and pull off clip on the bottom of the cooling fins that holds heating element.
To install new part I just reversed these steps.

Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

Defrosted coils with hair drier and after the freezer was turned back on the freezer cooled to 0 Deg. within 4 hours but coils collocted ice. Checked coil with ohmmeter OK replaced Defrost Assy. Repair was very easy and new replacment unit is sealed and the original is an open curcuit board. thanks for allowing me to share this with you!

This is the 2nd time I replaced the ADC, the freezer condenser was frosting up again and wouldn't keep the freezer or refrig cold. 1st part only lasted 6-months. The simple fact is that the ADC used in the Maytag as well as others is under designed; I purchased 2-this time, 1's a spare, and you know it going to need to be replaced again. Sadly I'm stuck with this Refrigerator for at least 2-years before I buy another, it's only 5-years old. From my experience (with other Maytag products I've purchased recently) I'd never buy another Maytag product, ever! Since Whirlpool bought Maytag, I'm taking Whirlpool off my list too. Thanks Partselect for such a speedy delivery on the part everything back to normal, at least for now, wished I knew how long this ADC will last?

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Popped the top cover of the handle to expose two screws at the top of the replacement handle. Removed those two screws to loosen the handle and expose the third screw at the bottom of the handle. Replaced the handle with the same 3 screws. Total time 10 minuets

Read wiring diagram found what would stop power to compressor. Removed thermostat checked for continuity which there was none no matter what position dial was in. Checked operation of remaining components in the refrigerator by jumping the two wires together that are connected to the thermostat, plugged refrigerator back in and compressor kicked right on.

Simple to fix. Watched the video and noted what to do.
Replaced the control board, solenoid, and limit switch. Woks like new!

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

My ice maker was overflowing and i realized that it was the water valve that needed replaced. unscrewed 1 nut, unhooked 3 water lines, unhooked electrical components and re-installed in reverse order. took about 10-15 mins.

As the previous users have stated, remove the ice tray, then remove the ice bin enclosure. Watch for the screws that are used to mount the enclosure.
As you slide the enclosure forward, go slowly, there is a wiring connector at the back, you will need to un-plug this connector. The solenoid assy is kind of tricky, as it is spring loaded, but easy to figure out. As previously mentioned, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). Be careful with that, as it is hard to hold on to the shaft while getting the yoke off. Now remount the motor, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, slide it the rest of the way in, tighten the screws, and you are ready to make ice again. Approx 30 minute job.