FLSC238DB1 Frigidaire Refrigerator - Instructions

Removed the fridge door, replaced plastic Hinge Bearing, re-attached door. WhaLa - No more clicking!

I followed the past suggestions and I opened the parts list to understand what was where. Caution when removing the face plate. The flat white connector pulls out easierly. It can be plugged back in after. I have big hands so it was hard to connect the water back to the unit. Other wise it went ok.
OH , make sure to unplug the refrigirator. I touch the control board and got snapped.

Removed Water drip tray, Then removed (3) screws holding the cover in place. Removed (3) more screws holding the circuit board in place. pulled out ribbon cable from the circuit board which is connected to cover, and put aside.
Tried to remove screws holding actuator in place, but it was a bit tight,,wish i would have tried to un-plug the connector on the left side first, but did not, i instead removed the water tube to gain better access,,,,replacing actuator was easy, re-attaching water tube was not simple at all,, but if you do end up pulling it out,,,do not waste time trying to pull it back thru, it is not nessasary, and impossible to do,,the end is tapered, and makes a pressure seal, so it will not leak,,,re-attached screws, ribbon cable, cover, and drip tray,,and done.

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

Replaced the Triple Water Valve

Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.

The door clunk problem was as others described. Repair similar to others described. The major thing to understand which I didn't see listed elsewhere is whether the top or bottom little nylon toothed cam is broken. This part is the one in the door. There was also one in the hinge, PS976594 or PS430814 ? I ordered this one and was lucky that it was correct. I'm not sure whether it's possible to know whether door side or hinge side is broken, without removing the door to see.

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

pried bottom plastic plate to expose two screws. popped frame of water/ice dispenser. loosened four tiny screws to remove mother board access acuator for replacement. snapped off two cable wires attached to the actuator and replaced it with the new actuator. reversed process and job completed in 35 minutes.

Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!