DWU9200ABE Maytag Dishwasher - Instructions

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

I removed the inside door cover, unpluged the accuator, removed the two screws holding the dispenser latch in place. Replaced both the latch and rubber groumet. returned the door to normal operation and verified no leaks was present.

Removed door interior, confirmed with tester that power was reaching door cut-off switch, but not power on other side of switch when engaged. Noticed that little switch button frozen in shut position, assumed switch had burned out. Installer new door cut-off switch with new (dual) switch units in place, plugged in unit and it ran perfectly.

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

Pulled out the old gasket and pressed in the new one. No more leakage.

Remove detergent cup lid by punching out retaining pin. Access hole is toward outside of door. I used a slightly curved dental tool because access hole is slightly below level of main door surface. Spring on opposite side of door will fall out. Insert spring into new door. Pre insert retaining pin partially into new door. Make sure that the curved end of spring is pointed toward the detergent cups when sliding door into position. When door is in position, squeeze the retaining pin fully into the receiver using the pliers.

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well