DWU9200ABE Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- marquis from wolcott, VT
- Parts Used:
- 911356, WP99001791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
food was pluging the sprayer holes
took the cover off and replaced the filter. It works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathy from grayslake, IL
- Parts Used:
- WP912653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
nothing held the door up
first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done
Was this instruction helpful to you?
Thank you for voting!
Tjhe nylon piece that attaches the spring to the door broke.
Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from San Antonio, TX
- Parts Used:
- WP99002003, WP902899
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rinse dispenser won't work
Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from San Antonio, TX
- Parts Used:
- WPY913158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking hose. Water coming out from under washer.
Turned off power. Removed lower, two panels. Turned power back on and started dishwasher. Saw leak from 7' drain hose. Turned off power, disconnected hose, ordered new hose, installed on washer and routed back to garbage disposal. Turned on power, checked for leaks (none) and replaced 2 front, lower panels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Asheville, NC
- Parts Used:
- 912647
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
A sudden puddle of water under the dishwasher
I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from Platteville, CO
- Parts Used:
- 902882
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
our dishwasher needed a motor shaft seal
I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from West Union, OH
- Parts Used:
- 903096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwater cold
I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from York, ME
- Parts Used:
- WP902899
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser door would not open
Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Palm Harbor, FL
- Parts Used:
- WP99002560
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not fill with water
Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Laingsburg, MI
- Parts Used:
- WP99002560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No water would enter in dishwasher
Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marguerite from Palm Bay, FL
- Parts Used:
- WP99002947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel broke on rack adjuster assembly on top rack
Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from portland, OR
- Parts Used:
- W10131752
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Leaking water at bottom left of dishwasher door
Initially thought this issue was the dishwasher door gasket, but after reading post on this site about door latch grommet, removed 7 "hex screws" pulled inside of dishwasher door away and traced water from leak back to soap dispenser latch/grommet area so instead of ordering door gasket ordered door latch and grommet. Replaced grommet only (in addition to 7 "hex screws" had to remove 2 additional screws to get to it) which took some maneuvering. Re-aligned grommet and latch, inserted and tightened all screws that had been removed. Works great - no more water leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- serafino from oakland, MI
- Parts Used:
- 99002254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not turn on
Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.
This was the third appliance I have repaired with the help of Parts Select in the last three months.
This was the third appliance I have repaired with the help of Parts Select in the last three months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from maple shade, NJ
- Parts Used:
- WP902461
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water wouldnt pump / making grinding noise
i removed the bottom spindle inside of the washer compartment. laid the pieces out in order of which they were removed. found the impeller was busted where it attaches to the shaft of the motor. screw was missing but found it laying in the bottom (there is a screen that filters the water as it drains). replaced impeller and put parts back together in order. good as new.
Was this instruction helpful to you?
Thank you for voting!