JDB3200AWB3 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The plate was missing at the time we purchased the house.
It was ok but screw holes were not in the right spot but we put one in and that is sufficient for now. It prevent thing from follow under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maynard from WISDOM, MT
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not drain water
Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from ROCKFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher Not Draining
The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WP717273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from COLUMBIA, NJ
- Parts Used:
- W10258275
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to control
0) assure main power was off
1) Opened up the panel assembly according to the instructions and the partselect video using the torx driver.
2) snipped the wires from the old part
3) patched in the new part by twisting the wire ends, inserting them into the assembly and tightening the screws.
Had my dishwasher up and running again within 15 minutes.
1) Opened up the panel assembly according to the instructions and the partselect video using the torx driver.
2) snipped the wires from the old part
3) patched in the new part by twisting the wire ends, inserting them into the assembly and tightening the screws.
Had my dishwasher up and running again within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from ELLINGTON, CT
- Parts Used:
- W11196317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaked bottom corner
Removed existing gasket by pulling up from the bottom edge. Clean groove where gasket came out of with a tooth brush and then replace gasket starting in the middle near the door latch. Make sure gasket is evenly distributed on both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from MELBOURNE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Timer repairs
Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.
Thanks you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSTOWN, PA
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spinner kept coming loose.
For easier access,removed both trays from dish washer. Pushed both clips apart from upper water arm, let arm hang, removed old spinner, replaced new spinner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from BRECKENRIDGE, MN
- Parts Used:
- W10648041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Whining noise from dishwasher when filling and leaking around overflow valve
Unplugged dishwasher and turned off water supply. Removed bottom panel. Put rag under valve and unscrewed water inlet. Used ratchet and socket to remove screw from valve. Disconnected wires. Disconnected outlet. Installed new valve opposite of disassembly. Turned water back on. Plugged in and checked for leaks. Test ran.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from San Jose, CA
- Parts Used:
- WP8564929
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken rinse aid cap
Just replaced the broken item with the new one..no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dylan from RIVERSIDE, CA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from BAINBRIDGE IS, WA
- Parts Used:
- W10258275
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bi-metal fuse ok. Wire to terminal block burned out.
Cut wires to terminal block, removed bi-metal fuse. Rewired to n ew terminal block and snapped on fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from LOS ALAMOS, NM
- Parts Used:
- W11196317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Leaking small leaks at the corners of the front door.
Installed the new tub gasket, fairly simple. Installed the bottom door seal not so easy. Leaks are still present.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!