Ryobi Pole Saw Parts
Find Parts Fast
Guaranteed Fit
Repair Videos
Popular Ryobi Pole Saw Parts
- Fix Number
- FIX9873442
- Manufacturer Part Number
- 099988002015
- Fix Number
- FIX9872907
- Manufacturer Part Number
- 099629001001
Fixes these symptoms
- Chain comes off guide bar
- See more...
- Fix Number
- FIX10022303
- Manufacturer Part Number
- 901289001
Fixes these symptoms
- Chain comes off guide bar
- See more...
Installation Instructions
Martin from MOBILE, AL
Defective power cord
Remove all the case screws and then the plastic cover. Pay careful attention to where everything is located, switch, safety lever, etc. With a small screwdriver loosen the 2 screws on the terminal strip holding the power cord's black and white wires. Remove power cord. Install new power cord ensuring you match the black and white wires to the terminal strip you just removed. Tighten terminal strip screws so that wires will not pull out when you tug on them. Reassemble making sure the power switch, safety lever and power cord are in their correct locations and install cover. Insert screws and tighten. Note! To avoid cracking case do not over tighten.
Read more...
- Fix Number
- FIX9939474
- Manufacturer Part Number
- 310983001
- Fix Number
- FIX9985138
- Manufacturer Part Number
- 610323001
- Fix Number
- FIX9873456
- Manufacturer Part Number
- 099988002033
Fixes these symptoms
- Will Not Start
- See more...
- Fix Number
- FIX9939669
- Manufacturer Part Number
- 311081002
- Fix Number
- FIX9873452
- Manufacturer Part Number
- 099988002029
- Fix Number
- FIX9873446
- Manufacturer Part Number
- 099988002021
Installation Instructions
Andreas from TUCSON, AZ
Motor burned out, need to replace the motor.
Step 1 - remove chain cover, chain guide plate and chain.Step 2- Remove all screws holding the casing together. Pay particular attention to the screws hidden under the Ryobi label (2 of them) - Use phillips head screwdriver.
Step 3 - Take photographs of how things are supposed to be when assembled with attention to the wire connectors on the motor to ensure polarity when reconnecting. (*super important otherwise you may be running the chain in the wrong direction and injury will occur.) Also take photo of chain side so that you re-stack the chain cog and washer correctly during reassembly.
Step 4 - Pull oil pump assembly off of inner case
Step 5 - flip over and remove snap ring on the axle using the snap ring pliers.
Step 6 - flip back over and pull the axle assembly apart so that the motor can be removed.
Step 7 - Once the motor is removed, remove the front bezel bracket from the motor. You will need this for the new motor. Make note of how it is mounted and remove the two screws. Immediately mount this bracket in the same position on the new motor while observing the polarity of the wire connections.
Step 8 - re-seat the new motor into it's place.
Step 9 - connect the terminals making sure the poles are correct. Use photos for reference.
Step 10 - re-insert the main axle with all wheels stacked and flip over to re-stack or re-insert the chain cog and washer as per photo.
Step 11 - Re-attach the snap ring using the snap ring pliers. Caution: make sure the the ring is properly held by pliers as it could spring off and cause eye damage and or just get lost.
Step 12 - Re-install the oil assembly using photo as reference for the pumping mechanism to be installed correctly against the ceramic off center wheel.
Step 13 - Fit cover on while making sure the bearing fits correctly. Don't force, just wiggle until the covers come together and seal nicely.
Step 14 - while holding the covers together, flip entire unit over and insert and screw in the screws.
Step 15 - Replace the chain guide plate, the chain and the chain cover.
Step 16 - add chainsaw oil
Step 17 - do some quick tests to make sure the chain is moving in the correct direction. It should be coming towards the saw head on the bottom side of the chain guide plate so that what you are cutting gets pulled towards you.
Step 18 - Go get you some cutting done! Read more...
- Fix Number
- FIX11858817
- Manufacturer Part Number
- 693814001
Appliance Type
Popular Ryobi Pole Saw Models
- P4360 (107369007) P4360 18 Volt Pole Saw Mfg. No. 107369007 1-24-22 (Rev:02)
- P4360 (107369001) P4360 18 Volt Pole Saw Mfg. No. 107369001 12-15-20 (Rev:06)
- P4360 18 Volt Pole Saw
- RY43160 Electric Pole Saw
- RY43161 Electric Pole Saw
- RY40051 ((311069004)) Pole Saw Attachment
- RY40050 Pole Saw Attachment
- TP26 Gas Pruner
- RY52014 (TP30) () Gas Pruner
- RY52604 Gas Pruner
- RY52604 (TP26) Ry52604 Gas Pruner (Tp26)
- RY15520 Pruner Attachment
- RY52004 Gas Pruner
- RY52502 Gas Pruner
- RY40051VNM ((316199001)) Pole Saw Attachment
- RYPRN33 ((090112021)) Expand-It Pruner Attachment
- RY52504 (TP30) Ry52504 Gas Pruner (Tp30)
- RY52504 Gas Pruner
- RY52903 Gas Pruner
- 135PR (505000001) Pruner