WWA5600SBLWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jacquelyn from Bokoshe, OK
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old knob broke
Opened the package - put it on just like the old one. Didn't take 5 minutes. Good as new.
Was this instruction helpful to you?
Thank you for voting!
oil leaking from under side
turned washer upside down- had to remove one frame cross member to get to the seal. replaced seal- replaced frame cross member. stopped the oil leak, but had a small rusted hole in the bottom tub. sanded that clean, inserted a rubber snap-in plug that fit the hole, covered with that monkey glue. let that dry for a while then covered that with BJ weld, let that cure 3 days. washer workes fine now no leaks at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zhiyong from North Potomac, MD
- Parts Used:
- WH1X2026
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Washer can drain but not spin, buring smell
Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillips J from Hot Springs Village, AR
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The tabs on the timer are broken off
I bought a timer dial knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Cape Coral, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic selector knob on front of dryer cracked
new knob fit onto 'd' shaped spindle. This took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from CHEVY CHASE, MD
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out selector knobs
Took off the broken ones and pushed on the new ones. Simple, simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Chesapeake, VA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out dryer knob
I just pulled the old part out using no tools with minimum pressure and pushed the new dryer knob in with no problems at all within approximately 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from ft riley, KS
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
No shake, but plenty of rattle.
We bought this used Hotpoint that was probably one of the original machine created back in the stone-age, it's so old. We've had it 10 months, and it's always had this... burnt rubber stink to it... then one day, it stopped agitating and sounded like a metal bucket of bolts being shaken. We're on a military income with five kids, and the idea of buying a new washer was just... heartbreaking. On a whim, having fixed a washer once before, we opened the front up and painstakingly pulled every last rubber fiber from what used to be the belt. Ordered the part. It shipped quick, arrived quick, and in under a week we were back in business. Someone else had mentioned the needing 1/4" socket, and I was glad I remembered that, because it made is SO much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allison from exeter, NH
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob broke
popped the new one on, and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- La Rae from Buda, TX
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke inside
Replacement knob went on without tools in 1 second.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Jackson, WI
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
knob broke
simply replaced knob, it took less than 15 seconds, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Reno, NV
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Selector Knob broke
Got online to PartSelect ordered part online using part find and order system (Sunday Night) received new part on the following Wednesday replaced (less than 5 mins) did the laundry. Thanks PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Glenolden, PA
- Parts Used:
- WH1X2754
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
timer knob just spins and would not set the time
I unplugged the washer from the outlet. I pulled out the timer knob and used needle nose pliers to remove the clip from the rear of the knob. I removed the old knob and inspected it. Sure enough, the teeth that engage the timer were worn down to the point where they no longer would engage and turn the timer. I installed the new knob and ghen installed the new clip to secure it to the timer. I plugged the power cord in and tested the washer.....done deal!!!! Parts Select made this job easy and saved me a lot of money by not having to call a service company. The part arrived in two days, it was the exact replacement part, it was good quality. I will do business with them the next time I need to repair an appliance. Great service, great web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- loring from pine bush, NY
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
knob broke off by clip
watched your video fixed it in a heartbeat I like the site very much also, I looked up the part in a minimum amount of time.I would say it took me 3 minutes total ordering and replacing Loring Gantner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Seven Hills, OH
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old knob broke at the stem.
KNob has gears that mesh with the washer. Simply put on the post and slid the clip into the groves on the stem. Pushed it on with needle-nosed pliers.
Was this instruction helpful to you?
Thank you for voting!