JKP07G*06 General Electric Wall Oven - Instructions

IT was fast and easy! Thanks

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi

Removed old part, install new one.

Took out the old and put in the new! Easy and inexpensive repair (especially because my husband did it!)

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed. Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!

Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!

I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.

I pulled it out a bit and exposed where the element screws into the power.

To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.

After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.

Reset the breaker, and you're good to go.

Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.

Turned off power at breaker and removed old element and replaced new element.

First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven

replaced with a new part . Thanks for all your assistance in getting the correct part

remove two screws from back of oven holding element to back of oven. Pull out gently, remove two screws holding wire connections(power wires) throw away old element. Place new element into oven. Reconnect element to power wires using screws. Push element back into back of oven. Replace screws holding element in place. Turn oven on to check for proper connections.

Our home was built in 1990 and has an original GE oven in it. When the bake element broke in half, I thought for sure it meant buying a new oven. When I looked on line and found Part Select.com, I was impressed to find the exact part I needed. I requested the part on Saturday, and it arrived on Tuesday. I installed the part on Saturday just in time for hosting our Super Bowl party and baking enchiladas! You guys saved the day! Thanks PartSelect!

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.