KBFS22EWBL3 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from HARRISBURG, PA
- Parts Used:
- W11346623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Head filter broke where you put the filter in
I watched a 5-minute YouTube video ordered the part. It was delivered fast and it took me about 30 minutes to put it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MIDDLETOWN, MD
- Parts Used:
- W11368721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right door seal was torn at top of door
I followed the remove and replace instructions in the Part Sect video when I ordered the seal. Pulled out the old seal by hand and installed the new seal. No tools needed, very easy. Took 10 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from KERRVILLE, TX
- Parts Used:
- W10884390
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was leaking
I first removed the door to the freezer (my frig has a bottom freezer) by loosening the 4 screws and lifting the door up and off. Then, because I'm stubborn, I chose not to remove either of the basket/drawers. It took a little bit of effort to fit my arms/hands in there, but I was able to remove the bottom screw to the old icemaker, and loosen the two top screws. (And disconnect the wiring harness.) I could then lift the old icemaker up and off. Putting the new icemaker in was pretty easy-- just slide it down over the two top screws and connect the wiring harness. The hardest part was getting the bottom screw back in! Because I didn't remove the baskets/drawers, I had very little room to work, and I had to "feel" for where that bottom screw went (even used a little mirror to help me). I could have just left this screw out, as the icemaker was sitting in there quite securely. But I kept at it, and after about 20 minutes, I was able to line up the screw with the hole, balanced on the tip of the screwdriver, and get it screwed in. Total repair took about 45 minutes. And no more leaky ice maker!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from STOCKBRIDGE, MI
- Parts Used:
- W11346623
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ICE MAKER WATER FILTER HEAD REPLACEMENT
AS PER A VERY GOOD VIDEO I FOUND SIMPLY BY SEARCHING FOR THE PART NUMBER. IT MAY HAVE BEEN ON THIS SITE. SADLY, THE PUSHING ON THE CONNECTOR WITH THE 1/2" WRENCH LOOKED A LOT EASIER IN THE VIDEO, OTHERWISE EASY PEAZY AND I HAVE VERY PAINFUL ARTHRITIS IN MY SHOULDERS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Circle, MT
- Parts Used:
- W11024089
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Evaporator motor failed.
Remove lower freezer door from mounting frame (4 screws). Remove inner shelving and shelving brackets, Total of six screws, three on each side on lower brackets and 4 screws, 2 on each side on upper brackets. Remove ice cube maker (4 screws). Remove thermometer frame from back cover and slide thermometer out of frame. Remove 4 screws from back cover and remove cover. Slide thermometer through hole in back cover. Remove 4 screws from evaporator motor housing. Gently pull plastic fan off of motor shaft. Remove motor from housing and install new motor. Reinstall all parts in the order removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from BATH, PA
- Parts Used:
- WP67002633
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked humid drawer
Complete replacement of the plastic drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Illyssa from GREELEY, CO
- Parts Used:
- WPW10662129, WPW10194431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Fridge and freezer were too warm
Chose these parts based on suggestion on this website, as well as other sites. They did not correct the problem. Shipping was also quite slow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from STATE COLLEGE, PA
- Parts Used:
- WPW10171529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Did not have a ice pan
Ordered and placed in the freezer under ice machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from COAL VALLEY, IL
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The old shelf shattered when we tried to clean it
Just slipped it in. I think it's a very poor design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Algona, IA
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice maker quit working
Unplugged wire plug, removed mounting screws and removed ice maker. Installed new unit by reversing steps--
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- T.W. from GREENWEL SPGS, LA
- Parts Used:
- W10827914
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door To Deli Fresh Broke In Half
Snap Out
Snap In
Yes That Easy!!
Snap In
Yes That Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from DEER PARK, NY
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker stopped working
I tested the ice maker first and got no response. So I bought the new ice maker and unplugged the connector in the back, loosened the 2 screws up top and took the bottom screw out. I took out the old one and then plugged the new one in and hung it back on the 2 loosened screws and put the bottom screw in and tightened the screws. I have to say it’s working great! Have plenty of ice again. Saved a lot of money by doing it myself. Buy your original model number part from Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lane from EVERETT, WA
- Parts Used:
- WP12722803B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
One of the plastic fasteners had broken so the entire part needed replacing.
Turned off power, Removed screw, disconnected wire harness and removed old rail from door, Connected new wire harness and attached new rail to door, replaced screw. Restored power. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from WINSTED, CT
- Parts Used:
- W10619951
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining to pan. It caused an ice build up under the freezer draw
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MABLETON, GA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Easy fix for Whirlpool refrigerator
I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!
Was this instruction helpful to you?
Thank you for voting!