10657903701 Kenmore Refrigerator - Instructions

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

Resistance on solenoid for water to ice maker measured low (5 ohms). I assumed the coil insulation had degraded because there was almost a short with such low resistance. Replaced the water inlet valve kit and ice maker filled with water and everything worked great. I had to cut the ends of the hoses because my model use compression fittings and this new valve kit used the push on fittings. No leaks no problems. The cables plugged in the opposite direction from the old valve kit, so I had to re-route the cable a little and create slack by removing from 1 cable clamp.

Water leaking from under refrigerator. Initially believed leak was from filter assembly. Removed filter and shut off water supply but leak appeared at different intervals again. Large puddle of water coming out from under refrigerator. Removed back lower panel and checked for leak, but didn't find any. My wife was also checking for leak and found a crack in drip tray. Only way we could get the drip tray out was to first remove front lower panel, disconnect and remove wiring harness in front of drip tray, unbolt water filter assembly, and unbolt water solenoid unit at rear of refrigerator. Their water lines connect to filter assembly. My wife controlled the water solenoid unit to give me play as I pulled the filter assembly out as much as I could from the front. I could now wiggle the cracked drip tray out from under the filter unit. Replaced drip tray and reinstalled wiring harness, water filter unit w/new filter, and re-bolted water solenoid unit at back of refrigerator. Replaced back lower panel after turning water back on and checking for leaks. Replaced front lower panel.

The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.

Removed 3 screws on the bottom of old ice maker in the fridge, slid out old ice maker, disconnected electrical cable,took out old ice maker. Take the plastic tray from bottom of old ice maker install on new ice maker, reconnect cable, slid in place, replace the three screws. About 3 hours later water ran in and new ice maker started to make ice. The only thing I missed was I didn't rinse out new ice maker before installation. If you don't rinse out new ice maker you have to throw away the first full bin of ice due to metallic taste.

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

New part slipped right into the studs and fit perfectly

First removed one screw from the bottom right bottom side of the unit. Removed the door from the front of the unit. Pushed up the locking tab on the left underside of the unit and pulled the unit partway out. Removed the plastic cover ( that was retained by the screw removed and disconnected the electrical connection) and finished removing the unit from the freezer. Removed the remaining three screws from the bottom of the unit and installed on the bottom of the new unit. I then slid the new unit partially in and connected the wiring harness and slid the rest of the way in guiding the water line into thepocket which was taller than the origional unit. Reinstalled the wire protective cover with one screw and the front cover back on the new unit. Done and is working great.

A service man who came to the house for another job said it was common for one solenoid on the inlet valve to fail while the other still worked, which explained why it would refill the ice maker but not dispense water. It was easy enough to unscrew the old valve from the frig frame and unscrew the and the tubing. The valve is oriented a little differently, but there was still room for it and enough tubing to reach the connections. Seems to me colors for the new water/ice controls were not exactly the same, so I would make a note of them (by following the tubing) when you disconnect them. The newer style push-in connectors were easy to hook up once I trimmed the a half inch or so from the end that had been crimped by the older compression fittings. Once I started using the water again, the occassional small puddles of water under the freezer door hinge disappeared. I was told this can happen when you stop using the water, and the water remaining in the tube that runs up thru the freezer door can freeze and thaw, producing a sweat that runs down the tube and out the hinge.

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

First, verified power supply. I have power at wall outlet, no power at compressor. Also noticed no condenser fan operation. Searched YouTube and watched a few diagnostic videos of how to test for proper operation of my model. Dropped the control panel down to reveal the thermostat switch and control board. Wiggled thermostat knob and compressor would work intermittently. Thermostat bad internally. Removed wiring connections, removed cover over temp.probe. slowly removed capillary tube. Removed plastic sheath from tube. Take your time installing new capillary tube into plastic sheath as not to kink and damage tube. Route the new tube back into position that the old one was in. Reinstall covers. NOTE: My wiring terminals on the new switch were in different locations but the switch was the same dimensions. I used a multi-meter to determine the correct wire locations on new switch and installed. Reconnected power and all works well now.

I removed cleaned & re-ionstalled the same unit. It started to slowly make ice and then stopped. I repeated the above procedure again and it started to work normally. I will keep the replacement icemaker as a handy spare. I fear it will fail again in the near future.

Heating element broke and fried the rest of the parts had to take out the bad parts and put in the new ones and it worked. i have fixed this problem three times now.

first i put in a new water inlet valve it did not solve the problem i waited 3 days then ordered the ice maker i put it in an it still did not work after 3 days i put in water in the ice maker by hand it still did not work i gave up then to my surprise 4 more days it started working still not sure what was wrong but i am glad it works now this was about a two week process one tip on getting ice maker out is to take the door that's covers ice maker off no tools needed then remove three screws slip it in an out there is a helpful video for water inlet thank you mike b

After deciding it was the unit itself and not a water celenoid I ordered it from parts select. Instead of 3 to 5 business days it arived the next day after ordering. I had previously removed and reinstalled the ice maker while trouble shooting. It was easy to change it out, and works perfectly.

I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem