1069304203 Kenmore Refrigerator - Instructions

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)

ordered the wrong part at first. Spoke to a service assistant, returned it and got the right part. Cut it to fit and inserted it. The Service assistant was very helpful, wish I used her first rather than the online system.

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the harness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!

My Whirlpool refrigerator frezzer was not defrosting and the refrigator was not cooling. I followed the symptom parts advise (Defrost Timer Kit and the Bimetl-Def)of P/S. I pulled out the refrigerator from it inclosure and unpluged it, (note the shelf supports, the thinner ones are on the left side) I remove the shelfs and their supports,I removed the interior back cover of the frezzer, using a hair dryer I melted the frozen ice from the frezzer coile. Once all the ice was melted away, I cut off the old BIMETL-DEF and attacth the new BIMETL-DEF making sure the color wires are match correctly and using electrical connection plugs and electric tape I reconnected the wires. (2) I followed the video instruction for replacing the Defrost Timer Kit I found it to be quite easy to follow. The most deficult part was trying to position my body to remove the screws. I used an old CREDIT CARD to remove the face of the Refrigerator control buttons in order to access the compartment which house the Defrost Timer kit. I removed the old Defrost time kit and replaced it with the new one (following the Video instruction). I replace the frezzer cover inserting the lower four screws then using an old Credit Card I forced the top end of the frezzer cover under its retaing wall. I then replace the remaining two screws. JOB DONE

I just followed the enclosed instructions

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

unpluged refrigerator. removed panel in front of fan. Removed the fan motor. Installed the new fan kit. Replaced the panel in front of fan. Pluged the refrigerator back in. The refrigerator runs a 100 percent better

R/R part, 3 screws reconnect 3 wires. easy.