L3882XVW Norge Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hudson from Cockeysville, MD
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element was completely gone.
Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Littleton, CO
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The bake element burst.
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Lakewood, CO
- Parts Used:
- WPW10162384, WP7407P182-60, 12400043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Oven door hinges broken
With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Neenah, WI
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven heating element burned out like a lit fuse!
Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paola from High Bridge, NJ
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just plugged the burner in and it was good to go.
The burner wouldn't work. I just plugged in the new one and all was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Allyn, WA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned in half
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Funston, GA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating to set temp. 100 degrees too cold
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Kerens, TX
- Parts Used:
- WP7403P238-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Infinite switch replacement.
I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I replaced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MILLARD from LOOKOUT MTN, GA
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
thermostat control for large eye on range
removed several screws, removed old controller, installed new controller buttoned back up works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BURBANK, CA
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original rack had melted plastic on it.
Removed the original rack. Checked dimensions, installed the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CENTERVILLE, OH
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Large burner was surging indicating infinite switch failed
Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.
Burner works great. This is a easy DIY fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- leland from CARTHAGE, NC
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
burner swith not working properly
removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from LE ROY, WV
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
could not regulate element
replaced control
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CONCORD, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Burner plugs were loose
used the supplied parts...very easy. The parts were exact replacements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wesley from ODENVILLE, AL
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
original fixture required bulb - this fixture (all-in-one) was great
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this instruction helpful to you?
Thank you for voting!