Models > JGS650SEF1SS > Instructions

JGS650SEF1SS General Electric Range - Instructions

Jump to:

All Instructions for the JGS650SEF1SS
106 - 120 of 254
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
SANDRA from FORT EDWARD, NY
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Oven Not Reliting For Cycle
Took bottom cover in oven off with screwdriver . Then remove two small bolts with socket to igniter , unplug from under stove and pull out from inside oven. Reverse to install. Wala done and working great.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from Westford, MA
Parts Used:
WB13K21
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Oven would't Heat!
I was at my in-laws and they expressed how they needed to buy a new stove, since it stopped working. They explained the problem to me and I immediately checked the broiled (it worked fine). Knowing that stoves have 2 electric igniters, i knew 1 was bad.
The site got me the part in 3 days (regular shipping).
The repair was pretty easy.
- Removed 2 screws that hold the floor of the oven.
- Removed 2 nuts that held the igniter to the oven.
- Removed the bottom drawer of the oven, and unplugged the igniter.
- Finally, I screwed in the new igniter, fed the wire down to the plug and plugged it in.
- Then I tested the oven before putting it back together, IT WORKED!)
The only negative was, when I was removing the racks and pans from the oven, one of them happened to be filled with oil for frying, and it got all over me. Be prepared for anything when working on someone else's appliance.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ed from Genoa City, WI
Parts Used:
WB13K21
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
igniter element oven replace
First removed 3 screws at burner front and back then pulled out lower storage drawer to disconnect plastic connector, removed and had to cut plastic connectors to use ceramic wire nuts (supplied with parts box) I had to work from underneath stove as well as in the oven it self, if the main door is easily removable it would have helped a great deal but four hours later
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from Brooklyn, NY
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Oven would not light
The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MELVIN from BROOKLYN, NY
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The oven would not light
I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Young O'Neill from Fairfield, NJ
Parts Used:
WB13K21
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Old Igniter Burned Out
I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
THOMAS from FLUSHING, NY
Parts Used:
WB13K21
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
replacing oven igniter
Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from Oxnard, CA
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Oven Would Not Light
Every part of the part replacement was easy with the exception of removing one of the two screws that were holding the igniter to gas bar. No fault of the part to be replaced in any way. One of the screws that hold the igniter to the gas bar stripped when I was attempting to remove it. Had to use a small cut off wheel and my dremel to cut the screw and then was able to remove it by screwing it all the way through the hole it was in. Then tapped the two existing screw holes to 10/32 and attached the igniter with new screws. Everything else was about as easy as you can get.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Crawfordville, FL
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Oven wouldn't light
Replaced the igniter. Quite simple.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ignacio from Houston, TX
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Over would not ignite
I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Millville, NJ
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Oven would not light.
First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from douglasville, GA
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
oven not lighting when turned on.
Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Laura from sayville, NY
Parts Used:
WB13K21
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
The igniter in the over burnt out
My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.

thank you
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
walter from newnan, GA
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
igniter light went out
removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chuck from Carroll, NH
Parts Used:
WB13K21
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
wouldnt light
removed oven door & broiler draw took out bottom panel in oven removed part from burner tube reinstalled everything piece of cake works great now
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGS650SEF1SS
106 - 120 of 254