JGB600EED1ES General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gabriel L from NEW YORK, NY
- Parts Used:
- WB2K68
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer gliders broke when someone pulled out the drawer with too much vigor.
Installation was super simple. Follow instructions that are on the site already. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FLAGSTAFF, AZ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't light
Remove interior bottom of oven, remove igniter screws, unplug igniter. reinstall igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from EL SOBRANTE, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas Range oven not heating/replaced new heating element
Removed oven shelves, removed lower cover, removed heating element, removed lower drawer and unplugged element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from NAPLES, FL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom badly marred after 16 years.
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Sheboygan, WI
- Parts Used:
- WB35X29668
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Oven door gasket was damaged and leaking
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karin from ARUNDEL, ME
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas burner wasn’t burning properly
I ordered the new burner head and replaced it and now it works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from PAINESVILLE, OH
- Parts Used:
- WB20K10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace temp sensor in gas range
Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from ST CLR SHORES, MI
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner cap wasn't working proper.
took burner off installed new one thank you for fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!