11078590400 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melody from TEXARKANA, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from TUSCARORA, NV
- Parts Used:
- W10828351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lint filter on dryer had broken apart
Replacement fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Newport, VT
- Parts Used:
- WP691366
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken belt
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from glenford, OH
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch was cracked
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ava from BALTIMORE, MD
- Parts Used:
- 349241T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer making excessive noise; then continued to blow circuit
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from EVEREST, KS
- Parts Used:
- 349241T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
rollers had been new too long!
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsey from Lancaster, PA
- Parts Used:
- 349241T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer was making a loud rattling noise and shaking
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this instruction helpful to you?
Thank you for voting!
Dryer was making all kinds of noises
After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from NORTH EASTON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ERIE, PA
- Parts Used:
- 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Noisy while in use.
Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from UPPR MARLBORO, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from BETHESDA, MD
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Lid switch failed, dryer stopped working
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from TRENTON, NJ
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer continued to spin when you raised the lid not shutting off
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Was this instruction helpful to you?
Thank you for voting!