65198438 General Electric Dryer - Instructions

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.