41791129 General Electric Dishwasher - Instructions

1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.

I pulled the dishwasher out from under the counter. Loosened the collar holding the sump housing to the pump motor. Unscrewed the cover inside the base of dishwasher to release the collection opening of the sump. It's very flexible so I pulled it out by hand. Put the new one in and screwed everything back down. Pushed the dishwasher back under the counter. Simple Simple Simple.

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Replaced door seal, right and left corner seals. Piece of cake. A five minute job.

Thanks

Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.

Just took the old rusty rack out and put the new one in its place.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

with electric power and water source turned off,I first bailed out the water from tub then I pulled dishwasher out from under cabinet . Then I removed the motor and pump and put it on the table. I took a digital photo so I could remember exactly how everything was assembled. I checked for clogs and damage and realized that the solonoid casing had melted around the armature link assembly . I Looked at diagram for parts name and number and ordered from parts select. In the meantime I put a temporary one feed valve on hot water feed line so I could have access to hot water in kitchen while I waited for parts wich were here in a couple of days. Put it all back and it runs fine. Thank for your help

On the GE Pot Scrubber 1120 model you do not even need tools to replace the parts that we replaced. We just pulled the corner baffles out and cleaned the corners before placing the new baffles in. For the door gasket, we just pulled the old gasket out and put the new one in the track that the old one came out of. We didn't have to take any door screws out to replace the gasket at all. It was very easy to do and no more leaks. You will have to push against the door to get it closed tightly the first time you use it since the new gasket has not been flattened by use. I ordered the gasket insert and used it since we had it but for this model we didn't really need it. I would suggest not ordering one for this model.

Replaced with a new rinse aid fill cap.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.