Ridgid Parts

Fix Number

FIX18693520

Manufacturer Part Number

290069160

This is a brush assembly, sold individually. It is always recommended to replace both carbon brushes at the same time, so please order accordingly. If the motor of your equipment is not running smoothly, in a lot of instances, it is because the brushes are worn and need to be replaced. When inspecting the condition of the carbon brushes during your regular maintenance, it is wise to also check the condition of the armature. This brush assembly, like all of our parts, is sourced right from the original manufacturer.

Fix Number

FIX18687273

Manufacturer Part Number

089037006016

This is an authentic replacement part sourced directly from the manufacturer. The handwheel grip is found in table saws from Ridgid. This part is made of high-quality plastic, and is attached to the hand wheel to make it easier to turn. You may require a screwdriver or wrench when replacing this item. This product is provided as an individual replacement part.

★★★★★

★★★★★

1 Review

Fix Number

FIX18693523

Manufacturer Part Number

290069406

Genuine Ridgid replacement part, this item is sold individually. 2 of these Brushes are needed for a set. This Brush includes the Brush, Brush Holder, Brush Spring and plug in terminal. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX11867132

Manufacturer Part Number

29823

This is a single OEM replacement caster for vacuums. The caster makes it so the vacuum is easily mobile. This is a very simple repair that will not require any tools. Simply pull it off to remove and press the new replacement caster in until it is secure. This caster is sold individually.

Fix Number

FIX18693574

Manufacturer Part Number

291131002

This is a single OEM brush assembly with the leads, wire, and spring included. The brush holder is sold separately. Carbon brushes are known to wear from normal use of the tool, so it is important to consistently inspect and replace them as instructed by the manufacturer. It is also advisable to replace both brushes at the same time even if only one appears worn. For this quick and easy repair you will need a screwdriver. Disconnect the tool, remove the brush caps, remove worn brushes. Insert the new OEM brush assembly and secure the brush cap.

Fix Number

FIX17016247

Manufacturer Part Number

12313R

Sourced directly from Ridgid, this OEM approved replacement Toggle Switch is designed for certain models of Ridgid Utility Vacuums. To see if your device is compatible, please see the "Model Cross Reference List" below. The primary purpose of the Toggle Switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in vacuums. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Toggle Switch is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX18693700

Manufacturer Part Number

300527002

This is an authentic 5-inch sanding pad assembly for a sander. It provides support for hook and loop sandpaper. This part is prone to deteriorate, especially if too much pressure is applied to the sander while in use. This creates too much heat, which wears the sanding pad much quicker. For this simple repair, unfasten the four screws attaching the pad to the sander, and fasten the new pad in its place. This OEM pad assembly is sold individually.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX18690189

Manufacturer Part Number

089290001054

This OEM approved replacement Handwheel is designed for use with specific models of Ridgid Table Saws. To ensure your saw is compatible with this part, please see the "Model Cross Reference List" below. The purpose of the handwheel is to raise and lower the saw blade. This Handwheel is made of durable black plastic, is approximately 4" tall, and is sold individually. If your Handwheel is visibly damaged or no longer properly moves the saw blade, it needs to be replaced. No tools are required for installation.

Fix Number

FIX18693541

Manufacturer Part Number

290108002

This is an individually sold carbon brush. Keep in mind that most power tools will have two of these, and it is recommended to replace them at the same time. The motor requires these brushes to conduct electricity to the armature. Due to constant friction, these brushes will wear and require regular replacing. For this fast and simple repair, use your screwdriver to remove the brush cap and this will give you access to the brush.

Fix Number

FIX18726545

Manufacturer Part Number

590936005

This is an OEM brake skirt for a random orbit sander, sold individually. The brake is located just above the pad. It rubs against the pad and prevents it from rotating when the sander is not touching the workpiece. Over the use of the tool, the brake skirt will wear out eventually. It will become evident that it is worn if the pad is rotating at a high RPM when the sander is not on the workpiece. This can cause a gouge when the sander first contacts the workpiece.