Miscellaneous Parts

Fix Number

FIX12008384

Manufacturer Part Number

SP0002498

This is a manufacturer-approved frothing disc, sold individually. This frothing disc creates a thick and creamy froth, suitable for cappuccinos. Slide the frothing disc onto the shaft at the base of the milk jug, ensuring the wide end is face down. Push it firmly until you hear a click. If the disc is not properly in place or it has become dislodged this can cause the milk to not swirl, a burnt milky smell, or a grinding noise. Make sure you always add ingredients slowly and in small amounts, as adding ingredients quickly can cause the disc to disengage or prevent it from spinning. The manufacturer recommends washing it by hand with warm soapy water to help it last longer. Be sure to wash and allow it to dry after each use.

Fix Number

FIX10131726

Manufacturer Part Number

44-70-0375

This is a manufacturer-approved sausage plunger for a caulk and adhesive gun. This part pushes the caulk through the gun. The plunger is attached to the plunger rod and fits snuggly inside the barrel. Due to the constant rubbing against the barrel, the sausage plunger will need to be replaced over time. For this repair, start by removing the cartridge from the gun by unscrewing the cartridge from the mounting cap. Pull the cartridge away from the plunger, and remove it from the rod. The new plunger can now be installed by placing it on the rod and securing it with the screw. To complete the repair, install the barrel back onto the gun.

Fix Number

FIX12008385

Manufacturer Part Number

SP0002499

This replacement latte frothing disk is a genuine OEM sourced part, not an aftermarket equivalent. It is specially designed for Breville milk frother. This item is used to make latte froth for smooth and silky milk. It is made out of plastic and it is sold individually. No tools needed to replace.

Fix Number

FIX11878393

Manufacturer Part Number

44-86-1400

It is an authentic manufacturer-sourced part that is supplied directly from the original equipment manufacturer for use with Milwaukee grease guns. This is the replacement self-locking retaining ring for the barrel assembly, please refer to the diagrams of your model for correct location and use of this hardware. Note this item is made of durable metal and it is sold individually.

Fix Number

FIX19506027

Manufacturer Part Number

1619PA5609

Fix Number

FIX11878449

Manufacturer Part Number

45-06-0890

This is the seal for the barrel assembly, please make sure to check appropriate diagram for correct location and use of this item. It is an authentic replacement part that is specially designed for use with a Milwaukee grease gun. Over time seals tend to deteriorate and shrink eventually requiring replacement. It is made from durable rubber material and it is sold individually.

Fix Number

FIX10131977

Manufacturer Part Number

44-86-1380

This is an authentic OEM part which is designed for use with Milwaukee tools. It is a special hardware which helps to secure components. This is an identical replacement for a damaged or a faulty part that was installed on a new unit. Check the appropriate diagrams for your model for the exact location and the correct installation of this retaining ring. You will need snap-ring pliers to remove the old part and secure the new one. One durable metal retaining ring is included.

Fix Number

FIX19502284

Manufacturer Part Number

1609B04462

This miter fence provides guided support for precise angled cuts on woodworking equipment. Its rigid construction helps maintain accuracy and stability during cutting. Replacing a damaged fence restores proper alignment and improves cutting accuracy.

★★★★★

★★★★★

1 Review

Fix Number

FIX11877438

Manufacturer Part Number

30-06-0205

This item is an original part from Milwaukee for use in grease guns. The barrel assembly attaches to the stamping plate. You may need a screwdriver when replacing this part. Over time this item may break or wear down and will need to be replaced. It is made of metal and plastic and is sold individually.

Fix Number

FIX11878423

Manufacturer Part Number

44-94-0075

This is the special plunger rod with a handle that provides a user with a comfortable grip to operate the tool. Unfortunately, over time it can wear out, get damaged or lost eventually requiring a replacement. Keep in mind this high-quality part is made of durable materials and is sold individually. This authentic component is supplied by the original equipment manufacturer for use with Milwaukee grease guns.