Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
Rear Drum Bearing WE3X75
Works With Model NJLR473GT0WW!
$18.68
In Stock
- Fix Number:
- FIX267865
- Manufacturer #:
- WE3X75
- Manufactured by:
- GE
Works With Model NJLR473GT0WW!
- Product Description
- This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.
- Works with the following brands:
- General Electric, Hotpoint, Whirlpool, Kenmore
- Works with the following products
- Dryer
- Fixes the following symptoms
- Noisy
- Part# WE3X75 replaces these:
- AP2042531, 3410, WE03X0037, WE03X0072, WE03X0074, WE03X0075, WE3X37, WE3X37R, WE3X72, WE3X72R, WE3X74, WE3X74R
Part Number Cross Reference
Product Description
This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.
-
Works with the following brands:General Electric, Hotpoint, Whirlpool, Kenmore
-
Works with the following products:Dryer
-
Fixes the following symptoms:Noisy
-
Part# WE3X75 replaces these:AP2042531, 3410, WE03X0037, WE03X0072, WE03X0074, WE03X0075 ... Show more , WE3X37, WE3X37R, WE3X72, WE3X72R, WE3X74, WE3X74R Show less
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts Additional or alternate parts to consider.
View More
View Less
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
squeaking when drying heavy loads
Remove 4 screws inside door and swing top back(hinges). Remove front by taking out screws(2) inside top corners and loosen screws(2) at bottom of panel. Swing panel to side of dryer; no need to disconnect any wires. Remove access panel on back of dryer and take off spring clip and washers from end of drum shaft. Pull drum forward abou
... Read more
t 6 inches(can do this without removing belt) remove old bearing and install new. Reinstall drum. Front slides are a simple remove and replace; helps to have something to hold drum up an inch or 2. Reassemble in reverse order
Read less
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Belt
The belt had broken on the dryer and I had purchased a replacement locally. What I found after dissembling the dryer was the drum slides, idler pulley wheel and rear drum bearing were very worn and needed replaced. Each were very easy to remove and replace. Slight challenges were lining up the pulley, reseating the drum with the belt a
... Read more
nd solving the how the two (belt and pulley) were configured. It did require a second person. Note: Do not drop any parts into the dryer when reassembling. It will require you to start all over.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud squeaking sound when dryer was running
Removed the 2 screws at top of open door to access top cover removal. Removed 2 screws at top of front face panel and took front off. Removed dryer tub , replaced bushing and the replaces sliders on front panel.Very easy
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX267865
Manufacturer Part Number: WE3X75
Manufacturer Part Number: WE3X75
Brand
Model Number
Description
✖
Mail-In Recycling Rebate