Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
Pump Connector WD18X10010
Works With Model EDW5000L15WW!
$40.11
In Stock
- Fix Number:
- FIX259530
- Manufacturer #:
- WD18X10010
- Manufactured by:
- GE
Works With Model EDW5000L15WW!
- Product Description
- The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure everything is fitted tightly. If there is a problem with the adapter, make sure to disconnect the water supply to your dishwasher before completing the repair.
- Works with the following brands:
- General Electric, Hotpoint
- Works with the following products
- Dishwasher
- Fixes the following symptoms
- Leaking, Not cleaning dishes properly
- Part# WD18X10010 replaces these:
- AP3185201, 943450
Part Number Cross Reference
Product Description
The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure everything is fitted tightly. If there is a problem with the adapter, make sure to disconnect the water supply to your dishwasher before completing the repair.
-
Works with the following brands:General Electric, Hotpoint
-
Works with the following products:Dishwasher
-
Fixes the following symptoms:Leaking, Not cleaning dishes properly
-
Part# WD18X10010 replaces these:AP3185201, 943450
Videos For installing this part.
Replacing your Pump Connector
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts Additional or alternate parts to consider.
View More
View Less
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- Bruce from Massapequa Park, NY
- Parts Used:
- WD18X10010
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Leaking water
I shut off electricity at the breaker and shut off water supply under the sink. Disconnected water line and electrical lines under the dishwasher. Removed 2 screws holding dishwasher to counter and pulled it out. Loosened hose clamps on connector and moved pump out of the way. Opened door and removed spinning washer blade and pulled water
... Read more
line from center piece. Used channel locks to loosen connector. From underneath, unscrewed connector. Screwed in new connector and put everything back together.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jared from Reinholds, PA
- Parts Used:
- WD18X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Pump connector pin hole leak
Turn off dishwasher breaker. Remove kick panel from front of dishwasher. Use nut driver to remove motor support, then loosen clamp from pump connector. Also loosen clamp on sump inlet and motor will drop down. Be prepared for water. Unscrew pump connector from bottom of tub. May need channel locks to loosen. Screw in new pump connector ma
... Read more
king sure to thoroughly tighten. Slide pump up into connector and sump and tighten clamps. Install pump support and replace kick panel. There is no need to slide unit out and flip over for this repair. If your pump is an inch or more off the floor you can do this repair without moving the unit.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Hummelstown, PA
- Parts Used:
- WD18X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
loud noise then wouldn't drain
Dishwasher started making violent noise at certain parts of the cycle. After a few weeks, it stopped draining the tub. Found that the drain pump stopped working and the rubber sump had degraded. While the rubber circulation pump connector appeared to be ok, it didn't reseal after pump/sump installation and had to be replaced as well.
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX259530
Manufacturer Part Number: WD18X10010
Manufacturer Part Number: WD18X10010
Brand
Model Number
Description
✖
Mail-In Recycling Rebate