Alpha Parts

Fix Number

FIX10261886

Manufacturer Part Number

516-25

This is a genuine OEM replacement part that has been sourced directly from Alpha. Vanes are found in variable-displacement pumps, which are used in many pneumatic tools. This four-pack of vanes is commonly used in pneumatic air polishers. Vanes are mounted on the rotor that spins inside the cylinder. They are durable, and they are designed to minimize the scratching of the cylinder, which will extend the life of your sander polisher.

Fix Number

FIX10261735

Manufacturer Part Number

210064

Fix Number

FIX12006084

Manufacturer Part Number

1030-0003

This is a genuine Alpha component which is supplied by the original equipment manufacturer for use with pneumatic air polishers. The hose connects to the unit for the water to travel through. Over time it may wear out or get damaged eventually requiring a replacement. Refer to the owner's manual for your model to ensure the correct application. Keep in mind this high-quality water hose assembly is sold as an individual item.

Fix Number

FIX10261930

Manufacturer Part Number

658-67

Fix Number

FIX10261456

Manufacturer Part Number

133034

This is a genuine Alpha replacement part. This brush terminal assembly is used in tile saws. There are two bushes, one located on either side of the motor they use electricity from the battery to energize the coils consecutively. As each one becomes energized its drawn to the magnets on either side of the armature, this is what drives it to spin. This bush terminal assembly is sold individually. Before attempting repair on your power tools make sure they are unplugged.

Fix Number

FIX10261455

Manufacturer Part Number

133033

This is a genuine OEM part that has been sourced directly from Alpha. This is a 2 piece set of carbon bushes commonly used in tile saws. These carbon brushes comes with wire lead and brush spring attached. Carbon bushes in your tile saw take the electricity from outside the motor and use it drive the spinning armature. Over time these carbon brushes will wear down, this is due to the amount of friction they experience. Signs your carbon brushes might be worn down are that the motor is running intermittently, there are electric breaking issues, and engine is experiencing reduced power. We recommend you replace both carbon brushes at the same time, even if only one is worn out. Before you begin this repair make sure you unplug your power tool.

Fix Number

FIX12006141

Manufacturer Part Number

658-95

An authentic OEM sourced part that is supplied for use with Alpha pneumatic air polishers. This is a high-quality replacement for a missing or damaged exhaust hose included with the new unit, make sure to refer to the appropriate diagrams of your model for the correct application of his component. It is made of high-quality leather material and is sold individually.

Fix Number

FIX10261909

Manufacturer Part Number

658-24

This is an authentic Alpha part made for use in air polishers. This brass nozzle fits into the gear shaft/spindle with an O-ring (part # 658-23) in between to prevent leaks and pressure loss. This nozzle is sold individually.

Fix Number

FIX10261905

Manufacturer Part Number

658-17

This item is an original part from Alpha for use in polishers. The spiral bevel gear attaches to the bearing. You may need a wrench when replacing this part. This item might break over time and will need replacing. It is made of durable materials and is sold individually.

Fix Number

FIX10261720

Manufacturer Part Number

210048

This is an authentic OEM replacement part that has been sourced directly from Alpha. These replacement carbon brushes are commonly used in sander polishers. Carbon brushes work to transfer electrical current to the armature inside the motor of your power tool. These parts are in constant contact with the spinning armature, the friction and heat they experience during operation is what leads to the brushes wearing down. When this happens you might notice your sander polisher has intermittent motor function, or the motor might have reduced power. When replacing carbon brushes you should always inspect the armature, if you find any burns, cracks, or other signs of damage this may indicate there are bigger issues with motor. This carbon brushes come with the wire lead attached. Before attempting repair on your power tools make sure they are unplugged.