OEM Jet Parts & Accessories

Tire

$40.28

Fix Number: FIX10375821
Manufacturer Part Number: 100025A

This manufacturer-approved tire is for band saws. Tire covers the wheel on which the blade rotates. The tire is a tight fit; stretch it around the wheel. Unplug the saw before installing this part. Wear work gloves to protect your hands.

Installation Instructions

Thomas from GROESBECK, TX

Tires were 14 years old and were getting rough

Step 1: Unplug band saw
Step 2: Remove Blade
Step 3: Use awl to pry up one edge of old tire, hold it up with your thumb and push the awl the rest of the way through, and pry the old tire off. (be careful not to mare the aluminum wheel with the awl.)
Step 4: Clamp the tire in one spot to the wheel, insert the tire until it will not go on anymore, clamp it at the point, work the tire on with both hands from that point until it is on the wheel, remove clamps, and seat the tire on the wheel. (use clamps that have padded covers where they touch the wheel, again making sure not the mare the wheel.
Step 5: Repeat Steps 3 and 4 for the other wheel.
Step 6: Re-install blade and set tracking and make coplanar adjustments. (hand rotate while setting tracking)
Step 7: Plug the band saw in
Step 8: Start the band saw and make sure it runs true. (It will run quieter as well)
Step 9: Have a nice day. Read more...

Crank Handle Assembly

$45.17

★★★★★

1 Review

Fix Number: FIX10376122
Manufacturer Part Number: 10601009

Rack

$69.59

★★★★★

4 Reviews

Fix Number: FIX10466766
Manufacturer Part Number: PM2800-071

Bushing- Oilite

$15.86

★★★★★

1 Review

Fix Number: FIX10378761
Manufacturer Part Number: 50-3105

Spring Cap Assembly

$29.29

★★★★★

1 Review

Fix Number: FIX10465183
Manufacturer Part Number: JDP17DX-078

This is a genuine OEM replacement part for select Jet and Powermatic Drill Presses. For full compatibility, please see the "Model Cross Reference List" below. This assembly is made out of metal and includes the Cap, Coil Spring, and Spring Retainer Ring. The primary purpose of this part is to allow the drill bit to be moved up and down by providing spring-loaded tension to bring the shaft to its original position. If your assembly vibrates during operation, or will not return to its original position, it likely is time to replace the Spring Cap. Each kit is sold individually.

Tire

$68.37

Fix Number: FIX10391908
Manufacturer Part Number: JWBS18DX-133

This genuine OEM supplied component is specially made for use with Jet and Powermatic band saws. Its purpose is to help track the blade on the wheel. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement to ensure best performance. Keep in mind this high-quality tire is made of durable rubber and is sold individually. Please make sure to refer to the owners manual of your model for the correct application of this part.

Ball Bearing

$40.28

Fix Number: FIX10463888
Manufacturer Part Number: BB-6203ZZ

This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

Installation Instructions

Adam from FREMONT, NE

Saw was making loud screeching noise and unsatisfactory cuts

1: disconnect power and remove blade
2: remove spanner nut
3: remove arbor nut. Spins opposite:
righty loosy lefty tighty
4: remove arbor with mallet and dowel
5: use arbor press to take off ball bearing
6: press on new bearing Read more...

Coil Spring w/Cover

$43.95

Fix Number: FIX10376155
Manufacturer Part Number: 10605002A1

Sourced directly from the manufacturer, this is an OEM approved replacement part for select Jet and Wilton Drill Presses. For full compatibility, please see the "Model Cross Reference List" below. The primary purpose of this part is to aid in adjusting the height of the drill. If your adjusting Wheel/Knob does not retract the spring, the spring may be damaged and should be replaced. It is made of durable metal, is approximately 2.75" in diameter, and is sold individually.

Bevel Gear

$8.54

★★★★★

1 Review

Fix Number: FIX10394572
Manufacturer Part Number: PGM-B02

This Bevel Gear is a genuine manufacturer sourced replacement part designed for use with Jet planers. To ensure this will fit your planer, please see the "Model Cross Reference List" below. This part is an essential part of the unit that allows the user to adjust the planers position. If you have difficulties adjusting the height, or if the gear teeth break, they need to be replaced. This part is approximately 1.1" in diameter, is made of durable metal, and is sold individually.

Eccentric Shaft

$6.09

Fix Number: FIX10467150
Manufacturer Part Number: PWBS14-240

Jet Parts

Popular Jet Parts

Installation Instructions

Installation Instructions

Appliance Type

Popular Jet Models

Jet Parts

Start With Your Model Number

Popular Jet Parts

Installation Instructions

Installation Instructions

Appliance Type

Popular Jet Models