OEM Murray Lawn Tractor Parts & Accessories

Lawn Tractor Mandrel Assembly

$48.56

★★★★★

1 Review

Fix Number: FIX12087499
Manufacturer Part Number: 587819701

Installation Instructions

Terrence from LORENA, TX

Blade mandrel replacement

1. Remove mower deck.
2. Remove mower blade from defective mandrel.
3. Clean caked up grass from underside of mower deck.
4. Remove belt pulley from top of defective mandrel.
5. Remove four bolts fastening defective mandrel to deck. Note: bolts will most likely shear - make sure you have new ones.
6. Install new mandrel to deck using four new self-tapping bolts.
7. Reinstall mower blade to new mandrel assembly.
8. Reinstall belt pulley to new mandrel assembly.
9. Reinstall mower deck to tractor. Read more...

Cap Axle Black 1 50 x 1 00

$3.99

Fix Number: FIX9007667
Manufacturer Part Number: 532104757

This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is goes missing or appears damaged. No tools are necessary for this easy repair, simply locate the cap axle on the rim of the wheel and remove.

Ring Klip Number T5304-75

$3.99

Fix Number: FIX9143890
Manufacturer Part Number: 812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Switch-Ign

$14.93

Fix Number: FIX9020864
Manufacturer Part Number: 532193350

This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and is enclosed in a plastic housing. A common sign that this part is malfunctioning is if the electric starter is not engaging. For this quick and easy repair, start by making sure the switch is in the off position and the key has been removed. Lift the hood up, locate the steering housing and press the tabs to disengage the old switch. Disconnect the wires and install your new OEM ignition switch.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

MICHELE h from ARGYLE, NY

Barely turns over to start, dead battery

Disconnected battery, unplugged key switch, using screwdriver removed old switch and replaced with new switch. Removed battery cables from old solenoid and replaced with the new one. End results still doesn't turn over enough to start it. Failed repairs Read more...

Welded Wheel Spindle - Right

$16.18

Fix Number: FIX17016482
Manufacturer Part Number: 538691201

Welded Wheel Spindle - Right

Nut, Hex, Flangelock

$4.99

Fix Number: FIX9022497
Manufacturer Part Number: 532409149

This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most models require three. For this repair you will need a wrench set.

Blade Mower

$16.18

★★★★★

1 Review

Fix Number: FIX9286056
Manufacturer Part Number: 532138971

This replacement blade is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. It is secured under the deck to cut the grass, over time the blade may become dull or damaged causing irregular cutting patterns. Inspect your blades periodically and replace them as needed to maintain a clean cut lawn. It is a high-quality component which is made of durable steel and it is sold individually.