OEM Magic Chef Wall Oven Parts & Accessories

Long Oven Sensor

$34.75

Fix Number: FIX1570174
Manufacturer Part Number: 12001656

This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temperature (too hot or not hot enough), not heating evenly, or an oven that will not start. To access this part, you will need access to the back of the range. Use a Phillips screwdriver to remove the screws on the access panel. Once the access panel is removed, you will notice a hole on the right side of the oven where the temperature sensor comes out of the oven. You will need to unplug the wire harness, and then open the oven door, locate it in the upper left corner, and remove the screws holding the temperature sensor in place. Pull the sensor out of the back of the oven, and replace it with your new part.

Fixes these symptoms

Door won’t open after self cleaning cycle
Element will not heat
Little to no heat when baking
See more...

Installation Instructions

Michael from Pearl River, NY

Oven did not heat up

Removed the oven door, removed existing screws. Pulled wire carefully out of opening, unclip connection. Reattached connection screwed back new sensor attached oven door finished. Read more...

Watch the install video

Flat Style Oven Igniter Kit

$57.79

Fix Number: FIX1573892
Manufacturer Part Number: 12400035

This flat style oven igniter kit is a genuine OEM replacement part for your gas range. When the igniter glows white hot, the heat opens the gas valve and ignites the fuel heating the burner assembly. If your igniter is only glowing orange or red, or not glowing at all, it will need to be replaced. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, and a variety of plug ends. This kit can be used for both short or long igniters, and the bake or broil element. However, it is not compatible with ranges that require round style igniters. The igniter has an amperage between 3.3 and 3.6. The element is very fragile and should be handled with care. Before beginning your repair be sure to disconnect both the power and gas supply to your range.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Gas smell
See more...

Installation Instructions

David from ENCINITAS, CA

Wall oven would take a very long time to ignite.

One of the 2 screws that holds the igniter to the burner assembly was stripped and difficult to get out. Other than that it was an easy fix. Read more...

Watch the install video

Terminal Block

$34.09

Fix Number: FIX11750972
Manufacturer Part Number: WPW10245259

It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).

Fixes these symptoms

Element will not heat
Little to no heat when baking
Touchpad does not respond
See more...

Range Bake Element

$103.52

★★★★★

2 Reviews

Fix Number: FIX11757472
Manufacturer Part Number: WPY04000066

This bake element with push on wire terminals is located in ranges and ovens. The terminal depth is 3 inches, the total element length is 19 and the wire terminals are 16 inches wide. Detailed installation instructions are found in the manual provided by the manufacturer. If your element is not heating then replacing it can solve your problem.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

GLENN from CHINO HILLS, CA

Bake element broke in half.

Disconnect electric.
Remove 2 screws.
Pull out old unit.
Disconnect wire connect tabs.
Install new unit.
Connect wire tabs.
Replace 2 screws Read more...

Watch the install video

Door Hinge

$98.27

★★★★★

2 Reviews

Fix Number: FIX11744215
Manufacturer Part Number: WP74008014

If your oven door is not opening or closing easily, there may be an issue with the door hinge. The hinge uses spring tension to allow the door to stay open at an angle instead of dropping open. This genuine OEM hinge can be used on either the left or righthand side of the door, and measures approximately 20.5 inches long. This part is sold individually, however we recommend replacing both hinges at the same time, as they can wear out a similar rate.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Carolyn J. from Oswego, KS

Oven door Hinge was broke...Door would just fall open

Watched the video on the repair you supplied...gave us confidence to make the repair. As easy as the video shows. We went ahead and bought 2 hinges and replaced both sides, since we had it apart...We, however, took the opportunity to take the door completely apart and clean it very good. Went back together easy. The new parts fit perfectly and my oven looks and works like it is brand new..New light bulb was a snap too. So glad I found this company....fast shipping too. Will always look here first in the future. Read more...

Door Hinge

$92.23

Fix Number: FIX2080677
Manufacturer Part Number: 74001984

This door hinge is a genuine OEM replacement part for your wall oven. Replacing this part will require partially removing your oven from the wall, to access the hinge. This part contains one hinge, although it is recommended to replace both at the same time. You will need a Phillips screwdriver to unscrew the hing assembly and install the new one.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Richard from SANTA CLARA, CA

Broken springs to the hinges

Power oven off from the circuit breaker.
Remove screw holding oven to wall.
Slide the oven away from the wall to clear
Hinges.
Remove nut screws and separate hinges
from each side.
Attach new hinges with springs to
oven sides.

Align holes to the threaded holes of hinges and put nut screws back in.

Note: threads on new hinges maybe
Roughly treaded. Don’t cross tread while
screwing in nutscrews.

Push oven back to wall and attach screws

Remount doors to hinges.

Turn circuit breaker back on. Read more...

Bake Element

$125.43

Fix Number: FIX11744515
Manufacturer Part Number: WP7406P272-60

This bake element is found on the bottom of the oven.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven not heating evenly
See more...

Installation Instructions

Susan from CHARDON, OH

The baking element split.

1. Turned off the electricity. 2. Removed the screws holding the old baking element in place in the back wall of the oven. 3. Pulled the element toward the front of the oven. 4. Used a screwdriver to slowly pry the wire clips, attached to the prongs on the element, toward the top of the oven. 5. Removed the old element, put the new one in place and slid the clips down over the prongs of the new baking element. 6. Slid the element prongs into the back wall of the oven and replaced the screws. 7. Turned the electricity back on. Read more...

Watch the install video