Models
>
GTW460ASJ8WW
GTW460ASJ8WW General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GTW460ASJ8WW
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
$84.03
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
In Stock
$48.30
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
In Stock
$13.32
This genuine OEM part is a lid lock striker for your washing machine. It is located on the lid of your washer and is used to activate the lid switch. The strike pushes against the lid switch to indica...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
The agitator rotates back and forth to move the clothes inside the tub to clean the load.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roy
December 18, 2022
Last night i heard water running. The water kept running and draining at the same time. I unplugged the washer and water didn't stop so i shut off the valve. This morning i yearned on the water and plugged the washer in. Now nothing. Is working. The lid closed light is on only.
For model number GTW460ASJ8WW
Hello Roy, thank you for contacting us. We would recommend checking the lid switch assembly, part number FIX16554755, and the water inlet valve, part number FIX12726769, and ensure their functionality. If this does not help, the issue is most probably related to the control board, part number FIX16743401. It manages the washer's functions such as filling, washing, draining, and spinning. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
Was this helpful?
Thank you for voting!
Related Parts:
James
December 24, 2023
I've just ran two loads of laundry, no issue. Started to run a "bulk" load setting(only 3 pair of tennis shoes) but gentler on tub and shoes than regular cycle. Now the motor is humming however the tub doesn't move. Belt or anything else I should check before ordering parts? Thanks!!
For model number GTW460ASJ8WW
Hello James, thank you for the question. Based on the description that you have provided, we would recommend checking the drive belt, part number FIX12299369. Good luck with your repair!
Was this helpful?
Thank you for voting!
Related Parts:
Gary
April 8, 2024
Water is constantly coming out of the drain while filling. What do you think would be the problem?
For model number GTW460ASJ8WW
Hi Gary, thank you for reaching out. We would suggest checking the water inlet valve first. If it is fine, the issue could be with the main control board, part number FIX17626552. You may need to replace it to fix the issue. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for GTW460ASJ8WW
Viewing 13 of 13Will not drain
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from NAPLES, FL
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Micheal from South Bend, IN
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Would not drain the water from the tub.
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from CLARKSVILLE, TN
- Parts Used:
- WH13X26535
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Cold water dripping inside of washer from inlet valve
Turn off hot and cold water supply valves feeding washer.
Disconnect both water hoses from washing machine.
Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve.
Slightly lift the bottom portion of metal plate and slide to release hooks for ... Read more easy removal.
Pull back and tilt forward plastic control panel to get it out of your way.
Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is.
Remove two screws from water inlet valve. (one on each side)
Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful.
Once you have disconnect the sensor you can remove the water inlet valve.
If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve.
The new valve DOES NOT come with a replacement O-ring so you
will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole.
Don't forget to install the O-ring or your washer WILL leak!
Put everything back together in reverse order.
Check hose connections for leaks.
Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.
Disconnect both water hoses from washing machine.
Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve.
Slightly lift the bottom portion of metal plate and slide to release hooks for ... Read more easy removal.
Pull back and tilt forward plastic control panel to get it out of your way.
Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is.
Remove two screws from water inlet valve. (one on each side)
Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful.
Once you have disconnect the sensor you can remove the water inlet valve.
If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve.
The new valve DOES NOT come with a replacement O-ring so you
will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole.
Don't forget to install the O-ring or your washer WILL leak!
Put everything back together in reverse order.
Check hose connections for leaks.
Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.
Read less
Was this instruction helpful to you?
Thank you for voting!