Models
>
KUDM01TJBT0
KUDM01TJBT0 KitchenAid Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KUDM01TJBT0
Viewing 12 of 12Manuals & Guides for KUDM01TJBT0
Click to downloadManual
Owner's Manuals
(2.04MB)
Manual
Owner's Manuals
(0.93MB)
Specs
Product Specifications Sheet
(0.03MB)
Keep searches simple, eg. "belt" or "pump".
$33.18
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check...
In Stock
$10.06
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
This black rubber gasket is a genuine OEM replacement part for your dishwasher door. The gasket helps to provide a tight seal between the door and the tub, preventing water from leaking while the appl...
In Stock
$44.78
This part contains the mounting clips and helps distribute water from the top of the dishwasher tub.
In Stock
In Stock
$35.51
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
In Stock
This part releases the detergent and rinse aid into the dishwasher.
In Stock
In Stock
$68.34
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
In Stock
In Stock
In Stock
$222.93
The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KUDM01TJBT0
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Fort Lauderdale, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Inver Grove Heights, MN
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more
it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Sunnyvale, CA
- Parts Used:
- 8193504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old upper wash arm fell off.
I dropped the upper rack to its lowest position.
I pulled the upper water channel down from the spring clip [on the top of the washer] to get access to the hole on the top of the front end of the channel. The front end of the channel only drops an inch or two.
I put the new upper wash arm pivot [larger of the two small pieces] ... Read more through the new upper washer arm from the bottom, placed the assembly up into the hole on the under side of the upper water channel, and snapped in the new keeper [smaller piece] through the hole in the top of the upper washer arm.
Finally, I snapped the upper water channel back into its spring clip. It was not even necessary to remove the racks.
There were no instructions or diagrams with the new parts, so it took me a few minutes to be sure which of the two small parts goes in from the bottom and which goes in from the top. Otherwise, I could have installed the new washer arm in one or two minutes.
I pulled the upper water channel down from the spring clip [on the top of the washer] to get access to the hole on the top of the front end of the channel. The front end of the channel only drops an inch or two.
I put the new upper wash arm pivot [larger of the two small pieces] ... Read more through the new upper washer arm from the bottom, placed the assembly up into the hole on the under side of the upper water channel, and snapped in the new keeper [smaller piece] through the hole in the top of the upper washer arm.
Finally, I snapped the upper water channel back into its spring clip. It was not even necessary to remove the racks.
There were no instructions or diagrams with the new parts, so it took me a few minutes to be sure which of the two small parts goes in from the bottom and which goes in from the top. Otherwise, I could have installed the new washer arm in one or two minutes.
Read less
Was this instruction helpful to you?
Thank you for voting!