66512774K312 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from BENICIA, CA
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking gasket
Easily pulled old gasket from channel. Soaked new gasket in warm water. Cleaned debris from channel with wire brush and CLR. Starting at top-middle, gently pressed new gasket in place. Used a gentle push-pull technique on the corners. Used fingers to smooth gasket all around. Closed door and kept latched for 2 hours. Ran dishwaher to check for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Essex, MA
- Parts Used:
- WP8269145
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from OAKLAND, CA
- Parts Used:
- W10712395
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Instruction from Whirlpool Not Good (No problem with Part Select)
Trial and error. The instructions from Whirlpool included with the part had minuscule pictures so it was hard to follow. The written instructions were good. But "a picture is worth a thousand words." Eventually it worked. The metal replacement part is much better the the plastic original. Not a good reflection on Whirlpool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Lancaster, NY
- Parts Used:
- WPW10705575
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Failed diagonistics test for OWI sensor
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LAKEWOOD, CO
- Parts Used:
- W10712395
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Roller wheel on dishwasher broke
OEM roller wheels were on plastic shaft which broke. Replacement was on stainless steel bracket with metal shaft, better quality. Don't think I will have to replace again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from PORTAGE, MI
- Parts Used:
- W10537869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Diverter valve was leaking.
After shutting off electricity, lay dishwasher on it's side (use a towel to absorb any water) then just use nut driver to remove faulty valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from Winchester, VA
- Parts Used:
- WP8270020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The Door Just Falls Down
After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from GRAPEVINE, TX
- Parts Used:
- WPW10497235
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Door leaking from corner.
First, I replaced the bottom door seal. You will need magnetic nut drivers because of the location of the 3/16 screws that hold the seal in place. you also need a 1/4 in nut driver to remove plastic cover that covers up the 5 3/16 screws. Last you need a small star driver to remove the door screws. Note 4 of the door screws, the 4 on top of the door are much longer than the side screws. With all this said, this seal was not my problem. I then replaced the large black rubber seal around the tub. Be sure if you do this you fold the seal in half and start in the middle of the top of the opening so you have the exact amount of seal left over on both sides. Also when you remove the old seal, clean the area it was removed from with a damp cloth. Turns out, That was not my problem either. So now I will move to the next step to see where the water is coming from but maybe this information will help someone with a simple door leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from WESTMONT, IL
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken cheap plastic wheels lower rack
Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.
Was this instruction helpful to you?
Thank you for voting!
Upper rack wheels had begun to break off. Shoddy design and materials.
I carefully followed the video instructions step by step. They were detailed, clear, and pointed out how to avoid installation mistakes. WIthout the video I would have been tempted to just figure it out myself - ("Hey, I'm a handy guy. How hard could it be, right?"). With the video I sailed right through with no dumb errors. The new rack adjuster wheel set is much sturdier than the Whirlpool original. It made sense to get new rack stops at the same time. Thank you, PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PERRY, MO
- Parts Used:
- W10537869
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking under the motor
Unplug the dishwasher,take the screws out of the coutertop,then slide dishwasher out turn it on its side. Then take a torx screwdriver and remove 2 mounting screws. Unplug the wires going into the motor and replace the motor with the new one. But you need to replace the grommet the motor shaft slides up into or it will still leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from AIKEN, SC
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from HALFMOON, NY
- Parts Used:
- W10712395
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The factory guide wheel snapped off of the plastic rack support
I followed the installation instructions included with the kit, they are not the clearest or the most detailed but they allowed me to finish the job in under 15 minutes. Only one side was broken but I replaced both sides in the time. Not a big job and very easy for a DIYer with average mechanical ability.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SEATTLE, WA
- Parts Used:
- W10712395
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rack adjuster wheel broke. Had to replace entir unit.
The install video was invaluable, and made installation a breeze. Unfortunately it did not include instructions to remove the original adjuster — which was of a slightly different design as the replacement. I eventually got the old part off using a screw driver to pry the plastic snap connections apart.
Was this instruction helpful to you?
Thank you for voting!